Restore your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected performance. Fortunately, resetting your Holosun is a straightforward process that can be achieved in just a few procedures.

• Begin by ensuring your red dot sight is powered on.
• Locate the small reset button on the bottom of the sight.
• Utilize a small object to activate the reset switch for approximately three moments.
• Let go the switch and your Holosun EPS Carry Red Dot sight will power cycle.
• The red dot sight should now be reverted to its factory settings.

Return to Your Holosun EPS Carry Red Dot to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to return to original, resetting it to its factory configuration is a breeze. First, locate the tiny button on the bottom of your optic. Then, keep pressed it for around five seconds until you see the red dot blink. Your Holosun EPS Carry is now returned to its factory settings, ready for consistent targeting.

revive your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

• Simultaneously press and hold the power button for approximately 10 seconds.
• A message will flash, indicating that the reset is in progress.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can re-attach the battery and confirm your sight's functionality. If you encounter any further troubles, don't hesitate to seek help from Holosun's support.

Restore Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

• Initially, Energize your Holosun EPS Carry by pressing the power button.
• Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
• As you continue holding these buttons, activate the power button once.
• The display will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to conclude. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Original reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight check here will then power off and restart with all settings Restored to their default values.

Reset your Holosun EPS Carry via a Factory Standard Settings

If your Holosun EPS Carry is acting up, a factory reset might be the solution. This will return your sight to its factory settings, clearing any personalized configurations you've made. To perform this reset, follow these easy steps:

• Initially, locate the reset button on your EPS Carry.
• Then, press a fine object, like a toothpick, to depress the reset button.
• As you hold the reset lever engaged, power on your EPS Carry.
• The sight will display a message indicating that the reset is finished.

When the reset is finished, your EPS Carry will be set to its factory settings.

Report this wiki page